Konfigurasi VLAN 1 Router untuk 3 Switch Cisco Packet Tracer

Konfigurasi VLAN 1 Router untuk 3 Switch Cisco Packet Tracer

Switch 1

Switch>en

Switch>enable

Switch#conf t

Switch(config)#vlan 50

Switch(config-vlan)#name dewi

Switch(config-vlan)#exit

Switch(config)#vlan 60

Switch(config-vlan)#name wulandari

Switch(config-vlan)#exit

Switch(config)#int fa0/1

Switch(config-if)#switchport mode access

Switch(config-if)#switchport access vlan 50

Switch(config-if)#exit

Switch(config)#int fa0/2

Switch(config-if)#switchport mode access

Switch(config-if)#switchport access vlan 50

Switch(config-if)#exit

Switch#conf t

Switch(config)#int fa0/3

Switch(config-if)#switchport mode access

Switch(config-if)#switchport access vlan 60

Switch(config-if)#exit

Switch(config)#int fa0/4

Switch(config-if)#switchport mode access

Switch(config-if)#switchport access vlan 60

Switch(config-if)#exit

Switch(config)#

Switch(config)#int fa0/5

Switch(config-if)#switchport mode trunk

Switch(config-f)#exit

 Switch 2

Press RETURN to get started.

Switch>en

Switch>enable

Switch#conf t

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)#vlan 50

Switch(config-vlan)#name dewi

Switch(config-vlan)#exit

Switch(config)#vlan 60

Switch(config-vlan)#name wulandari

Switch(config-vlan)#exit

Switch(config)#int fa0/1

Switch(config-if)#switchport mode access

Switch(config-if)#switchport access vlan 50

Switch(config-if)#exit

Switch(config)#int fa0/2

Switch(config-if)#switchport mode access

Switch(config-if)#switchport access vlan 50

Switch(config-if)#exit

Switch(config)#int fa0/3

Switch(config-if)#switchport mode access

Switch(config-if)#switchport access vlan 60

Switch(config-if)#ex

Switch(config)#int fa0/4

Switch(config-if)#switchport mode access

Switch(config-if)#switchport access vlan 60

Switch(config-if)#exit

Switch(config)#

Switch>en

Switch>enable

Switch#conf t

Switch(config)#intgigabitEthernet 0/5

Switch(config-if)#switchport mode trunk

Switch(config-if)#

ROUTER 1

 --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: n

Press RETURN to get started!

Router>en

Router>enable

Router#conf t

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#int gig

Router(config)#intgigabitEthernet 0/0

Router(config-if)#ip add 192.168.10.5 255.255.255.252

Router(config-if)#no shut

Router(config-if)#

%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up

Router(config-if)#exit

Router(config)#int gig

Router(config)#intgigabitEthernet 0/0

Router(config-if)#ip add 192.168.20.1 255.255.255.0

Router(config-if)#no shut

Router(config-if)#exit

Router(config)#int gig

Router(config)#intgigabitEthernet 0/0.50

Router(config-subif)#encapsulation dot1Q 50

Router(config-subif)#ip add 192.168.50.135 255.255.255.128

Router(config-subif)#exit

Router(config)#intgigabitEthernet 0/0.60

Router(config-subif)#

Router(config-subif)#encapsulation dot1Q 60

Router(config-subif)#ip add 192.168.60.71 255.255.255.192

Router(config-subif)#exit

Router(config)#